Originally posted by Liebones
Announcement
Collapse
No announcement yet.
Làm sao để đổi password Router?
Collapse
X
-
Quote:
Router> enable ==>vô privilege mode
Router# conf t ==> vô global configuration mode
Router(config)# line vty 0 4 ==> vô line config mode. Router cho phép 1 lúc 5 telnet session tương ứng với line vty 0 --> 4
Router(config-line)# login ==> hỏi password lúc login
Router(config-line)# password [password]==> cho phép telnet vào router
Sau khi config xong, bạn nhớ trở về privilege mode (nhấn Ctrl_Z), sau đó dùng lệnh copy run start để lưu cấu hình lại.
Hope this help
Thân mến,
Cảm ơn các bạn!
Mình đã làm như trên nhưng ko được. Mình đang xài Router Cisco 1700. Sau khi hoàn tất các lệnh mình dùng lệnh copy run start thì nó hỏi như sau: Destination filename [startup-config]?. Hihi..đến đây vì không biết làm gì nữa (vì các bạn không chỉ mà ) nên mình Enter luôn. Sau khi Enter nó báo như sau:
Building configuration...
Như vậy là được chứ, có thể dùng lệnh wr (write memory) thay lệnh copy run conf startup config.
Nếu như không thích bạn có thể xoá toàn bộ rồi cấu hình từ đầu.
Comment
-
Qui trình khôi phục password (password recovery)
I. Đối với Cisco 1600, 1700 and 2600 Series Routers:
1. Vào HyperTerminal (Private Edition 5.0 or higher) console.
2. Tắt router, sau đó bật lại. Nhấn Ctrl-Break trong vòng 60 giây
monitor: command "boot" aborted due to user interrupt
rommon 1 >
3. Dùng lệnh confreg để đổi nội dung thanh ghi sang 2142.
rommon 1 >confreg 0x2142
4. Reboot the router with the reset command.
rommon 2 >reset
5. Sau khi reboot, dùng Ctrl-C để vào user mode:
router>
6.
router>enable
router#copy startup-config running-config
7.
router>enable
router#show startup-config
8. Đặt lại password mới:
router#config term
router(config)#enable secret newpassword
router(config)#enable password newpassword
router(config)#line con 0
router(config-line)#login
router(config-line)#password newpassword
router(config)#line aux 0
router(config-line)#login
router(config-line)#password newpassword
router(config)#line vty 0 4
router(config-line)#login
router(config-line)#password newpassword
9. #copy run start
10. Khôi phục giá trị thanh ghi về 0x2102
router#config term
router(config)#config-register 0x2102
router(config)#exit
router#copy running-config startup-config
11. Kiểm tra nội dung thanh ghi
router#show version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE
SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 17-Aug-99 13:18 by cmong
Image text-base: 0x80008088, data-base: 0x80CB67B0
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
1 FastEthernet/IEEE 802.3 interface(s)
2 Low-speed serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2142 (will be 0x2102 at next reload)
II. Cisco 2500 Series Routers:
1. Thiết lập HyperTerminal (Private Edition 5.0 or higher) console .
2. Tắt routers, sau đó bật lại. Nhấn CTRL-BREAK trong vòng 60 giây.
Abort at 0x10EA884 (PC)
>
3. Đổi nội dung thanh ghi thành 0x2142
>o/r 0x2142 (lower case of the letter O for o/r and zero for 0x2142)
4. Reboot router
>i
5. Nhấn Ctrl-C để vào user mode khi router khởi động lại
router>
6. Vào enable mode
router>enable
router#copy startup-config running-config
7. Thực hiện các lệnh show running-config or show startup-config
router#show startup-config
8.
router#config term
router(config)#enable secret newpassword
router(config)#enable password newpassword
router(config)#line con 0
router(config-line)#login
router(config-line)#password newpassword
router(config)#line aux 0
router(config-line)#login
router(config-line)#password newpassword
router(config)#line vty 0 4
router(config-line)#login
router(config-line)#password newpassword
9. Copying the startup-configuration to running-configuration. Thực hiện lệnh no shutdown trên tất cả các interface được dùng.
10. Chuyển nội dung thanh ghi về giá trị ban đầu. Lưu cấu hình
router#config term
router(config)#config-register 0x2102
router#copy running-config startup-config
11. Kiểm tra thanh ghi có giá trị là 2102 bằng lệnh show version
router#show version
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-D-L), Version 12.0(4), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE
SOFTWARE (fc1)
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2142 (will be 0x2102 at next reload)
12. Reboot the router.
router#reloadEmail : vnpro@vnpro.org
---------------------------------------------------------------------------------------------------------------
Trung Tâm Tin Học VnPro
149/1D Ung Văn Khiêm P25 Q.Bình thạnh TPHCM
Tel : (08) 35124257 (5 lines)
Fax: (08) 35124314
Home page: http://www.vnpro.vn
Support Forum: http://www.vnpro.org- Chuyên đào tạo quản trị mạng và hạ tầng Internet
- Phát hành sách chuyên môn
- Tư vấn và tuyển dụng nhân sự IT
- Tư vấn thiết kế và hỗ trợ kỹ thuật hệ thống mạng
Network channel: http://www.dancisco.com
Blog: http://www.vnpro.org/blog
Comment
-
Admin oi ! Hinh nhu không phải router 2500 series nào cũng làm như trên đuợc đâu. Điển hình là cái 2501:
1. Cấu hình Hyper Terminal vớii các thộng số như bình thường.
2. Ctrl - Break trong lúc router khởi động.
3 Tai rommon
>o
>o
Configuration register = 0x2102 at last boot
Bit# Configuration register option settings:
15 Diagnostic mode disabled
14 IP broadcasts do not have network numbers
13 Boot default ROM software if network boot fails
12-11 Console speed is 9600 baud
10 IP broadcasts with ones
08 Break disabled
07 OEM disabled
06 Ignore configuration enabled
03-00 Boot file is cisco2-2500 (or 'boot system' command)
>o\r 0x2142
>i (to restart router)
Sau khi restart:
Router#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#conf
Router(config)#config-register 0x2102 (trả về giá trị default)
Router(config)#
Lưu cấu hình.
Comment
-
Originally posted by calvinHainchain vô trang web http://www.cisco.com/warp/public/474/ tham khảo nhé.
Comment
-
Re: Làm sao để đổi password Router?
Originally posted by notmeCác bạn cho mình hỏi, mình có một Router và khi mình Telnet đến nó thì nó hỏi pass, mình thấy cái pass này dùng cũng đã lâu quá rồi nên mình muốn đổi nó, vậy mình cần phải đánh lệnh gì? Mong các bạn chỉ từng bước cụ thể. Cảm ơn nhiều!
username username password password
Chúc thành công
Comment
-
RE: Làm sao để đổi password Router?
tôi thấy bài này post lên đã cũ rối , nhưng hôm nay tôi mới đọc , và thấy vẫn chưa hài lòng lắm , nên xin mạo muội cho thêm cái ý kiến :
Trước hết bạn phải mô tả chính xác việc login bằng telnet thì quá trình hỏi password là như thế nào :
1 / Nếu bạn phài nhập username và password để login vào thì do router của bãn cấu hình theo dạng : aaa authentication login default local (bạn sh conf lên để check thử), lúc này bạn phải đổi password theo user :
#conf t
<config>#username <youruser> password <yourpass>
<config>exit
#wr mem
2/ Neu như mới telnet vào thì router hỏi password liền thì đó là password cấu hình cho vty
bạn làm như sau :
#conf t
#line vty 0 4
#login
#password <yourpass>
#exit
#wr mem
Ban không cần phải reboot lại router , chỉ cấn thóat ra ngòai và telnet lại là OK
Comment
-
hey,
mình chỉ co thể recovery password khi router o conf register la 0x2142
ko biết khi đổi password có cần phải đổi conf reg từ 0x2102 sang 0x2142 ko nhi?
Su huynh experienced rồi trả lòi dùm Thủy hen.********************************
Truong Thanh Thuy
University of Southern California
Computer Engineering & Computer Science
Email: thuyusc@gmail.com
Phone: 08.44585659
********************************
Comment
-
RE: Làm sao để đổi password Router?
xin chào thuy
Nội dung thanh ghi là 0x2142 có nghĩa là bỏ qua nội dunh thanh ghi khi router khởi động lại. Nếu chỉ đổi password thuần túy thì không cân thay đổi nội dung thanh ghi
cám ơnNguyễn Hữu Hòa, CCNA
CCNP in progress
Comment
Comment