Tweet
Here you will find answers to Multiple Choice Questions
1)FCAPS is a network maintenance model defined by ISO. What does it stand for?
A – Action Management
B – Fault Management
C – Configuration Management
D – Protocol Management
E – Security Management
Answer: B C E (Fault, Configuration & Security Management) Notice that A stands for Accounting, not Action.
2) Which alerts will be seen on the console when running the command: logging console warnings.
A – warnings only
B – warnings, notifications, error, debugging, informational
C – warnings, errors, critical, alerts, emergencies
D – notifications, warnings, errors
E – warnings, errors, critical, alerts
Answer: C (warning, critical, alert, emergencies)
Explanation
The Message Logging is divided into 8 levels as listed below
Level Keyword Description 0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist 3 errors Error conditions exist 4 warnings Warning conditions exist 5 notification Normal, but significant, conditions exist 6 informational Informational messages 7 debugging Debugging messages The highest level is level 0 (emergencies). The lowest level is level 7. If you specify a level with the “logging console level” command, that level and all the higher levels will be displayed. For example, by using the “logging console warnings” command, all the logging of emergencies, alerts, critical, errors, warnings will be displayed.
In this question, E is also correct but it is less information -> C is the best answer.
3) You have 2 commands used for ftp:
ip ftp username xxxxxx
ip ftp password yyyyyy
Which two commands will be used when switching from ftp to http?
Answer:
ip http client username xxxxxx
ip http client password yyyyyy
4) Which two of the following options are categories of Network Maintenance tasks?
A – Firefighting
B – Interrupt-driven
C – Policy-based
D – Structured
E – Foundational
Answer: B D
5) The following commands are issued on a Cisco router:
Router(config)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(config)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
Router#debug ip packet 199
What would be the output shown on the console?
A – All IP packets passing through the router
B – Only IP packets with the source address of 10.1.1.1
C – All IP packets from 10.1.1.1 to 172.16.1.1
D – All IP packets between 10.1.1.1 to 172.16.1.1
Answer: D
Only communication between host 10.1.1.1 and host 172.16.1.1
6) You have two NTP servers 10.1.1.1 & 10.1.1.2 and want to configure a router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which command will you use?
Answer:
ntp server 10.1.1.1
ntp server 10.1.1.2 prefer
(notice the answer with the word “prefer”)
7) The interface is up and protocol is up. What level of logging is enabled when you get these messages?
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
%LINKDOWN‐3‐SERIAL:
A -alerts
B – errors
C – critical
D – notifications
Answer: D
8) Two Cisco routers are connected to each other and are enabled CDP. Serial line is up,protocol is also up but cdp neighbor not working. What layer of the OSI model does the problem most likely exist?
Answer:
Data link layer.
1)FCAPS is a network maintenance model defined by ISO. What does it stand for?
A – Action Management
B – Fault Management
C – Configuration Management
D – Protocol Management
E – Security Management
Answer: B C E (Fault, Configuration & Security Management) Notice that A stands for Accounting, not Action.
2) Which alerts will be seen on the console when running the command: logging console warnings.
A – warnings only
B – warnings, notifications, error, debugging, informational
C – warnings, errors, critical, alerts, emergencies
D – notifications, warnings, errors
E – warnings, errors, critical, alerts
Answer: C (warning, critical, alert, emergencies)
Explanation
The Message Logging is divided into 8 levels as listed below
Level Keyword Description 0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist 3 errors Error conditions exist 4 warnings Warning conditions exist 5 notification Normal, but significant, conditions exist 6 informational Informational messages 7 debugging Debugging messages The highest level is level 0 (emergencies). The lowest level is level 7. If you specify a level with the “logging console level” command, that level and all the higher levels will be displayed. For example, by using the “logging console warnings” command, all the logging of emergencies, alerts, critical, errors, warnings will be displayed.
In this question, E is also correct but it is less information -> C is the best answer.
3) You have 2 commands used for ftp:
ip ftp username xxxxxx
ip ftp password yyyyyy
Which two commands will be used when switching from ftp to http?
Answer:
ip http client username xxxxxx
ip http client password yyyyyy
4) Which two of the following options are categories of Network Maintenance tasks?
A – Firefighting
B – Interrupt-driven
C – Policy-based
D – Structured
E – Foundational
Answer: B D
5) The following commands are issued on a Cisco router:
Router(config)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(config)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
Router#debug ip packet 199
What would be the output shown on the console?
A – All IP packets passing through the router
B – Only IP packets with the source address of 10.1.1.1
C – All IP packets from 10.1.1.1 to 172.16.1.1
D – All IP packets between 10.1.1.1 to 172.16.1.1
Answer: D
Only communication between host 10.1.1.1 and host 172.16.1.1
6) You have two NTP servers 10.1.1.1 & 10.1.1.2 and want to configure a router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which command will you use?
Answer:
ntp server 10.1.1.1
ntp server 10.1.1.2 prefer
(notice the answer with the word “prefer”)
7) The interface is up and protocol is up. What level of logging is enabled when you get these messages?
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
%LINKDOWN‐3‐SERIAL:
A -alerts
B – errors
C – critical
D – notifications
Answer: D
8) Two Cisco routers are connected to each other and are enabled CDP. Serial line is up,protocol is also up but cdp neighbor not working. What layer of the OSI model does the problem most likely exist?
Answer:
Data link layer.